3, the calculation of corrugated carton load

Under normal stacking conditions, the bottommost cartons are under the most stress and are most likely to fail due to collapse. In theory, the pressure on the bottommost carton is:
P=W(n-1)Ã—9.81 (5)
In the formula: P-normal stacking under the pressure of the bottom of the carton (N);
N-stacking number.

Corrugated boxes are inevitably affected by external factors such as conditions of use, storage environment, and placement time. These external factors will cause changes in the compressive strength of the carton. From the point of view of equivalent effects, the compressive strength of the carton The change is completely equivalent to the change in the opposite direction of the external load to which it is subjected, and thus the range of variation of the external load of the corrugated box during the flow can be obtained. This article mainly considers the following factors.

(1) Air humidity The author has reviewed the report on the air humidity in the weather forecast of Wuhan Meteorological Bureau over the years. The change range is 65% to 90%. Changes in the air humidity within this range will result in a reduction in the compressive strength of the carton by approximately 24% to 45%, which is equivalent to an increase in the external load (same as below).
(2) Storage time Milk has a short shelf life, generally 0 to 10 days. The resulting decrease in intensity is about 0-20%.
(3) Stacking mode Normal stacking causes a decrease in strength of about 15 to 20%.
(4) Vibration and Shock of Transportation Tools The vibration and impact of the corrugated carton during transportation will cause the compressive strength to drop by about 20%. However, milk with a short shelf life is generally not transported to a remote place. Therefore, the value of the intensity reduction caused during transport is much smaller than that of general packaged goods. This article considers it to be 0 to 10%.

Assume that the above factors are independent of each other. Their final integrated impact on the load outside the carton can be seen as the product of the effects of all the independent factors under their own influence. From reliability theory, the distribution model of the external load should be a lognormal distribution. It is known that the weight of a single carton is 0.3kg, the weight of milk is 10kg, and the stacking layer number is 15 layers. Based on formula (5) and the above analysis, it can be concluded that the upper and lower limits of the change range of the external load of the carton during circulation are:

The upper limit: (15-1) Ã— 10.3 Ã— 9.81 Ã— (1 + 0.24) Ã— 1 Ã— (1 + 0.15) Ã— 1 = 2017.2 N
The lower limit: (15-1)Ã—10.3Ã—9.81Ã—(1+0.45)Ã—1Ã—(1+0.20)Ã—(1+0.20)Ã—(1+0.10)=3249.1.2 N
The author believes that the load S outside the carton obeys a lognormal distribution, and the probability that its random variation value lies between the upper and lower limits of the variation range calculated in this paper is about 99.74%. The average value of the external load can be calculated from the 3Î´ rule in probability theory. And standard deviation (see Table 1).

4, corrugated box reliability analysis

4.1 Reliability Calculation

Corrugated box limit state function based on ultimate compressive capability can be expressed as:
g=CrR-CsS (6)
In the formulas, R and S are the ultimate compressive strength of the corrugated box and the external load during the flow; Cr and Cs represent the uncertainty of the analytical model of the compressive strength and external load of the corrugated box.
Substituting equation (4) into (6) yields:
g=Cr [22.24(R1+R2)+32.84Rm-11849]-CsS (7)
This paper assumes that each basic random variable in formula (7) is independent of each other, and their probability distribution models and statistical characteristics are shown in Table 1. JC method was used to calculate the reliability index of corrugated box based on ultimate compressive strength Î²=0.5166 and reliability pr=0.6973.

4.2 Sensitivity analysis

Table 2 shows the calculation results of the sensitivity factors of each basic random variable. As can be seen from Table 2, the uncertainty of the corrugated cardboard box compressive strength and external load analysis and calculation model is the most important. Followed by the corrugated core paper ring pressure strength and external load, face paper and paper in the ring pressure strength is more.

4.3 Analysis of safety factor

Because the carton compressive strength and external load are random variables. Naturally, the safety factor defined as the ratio of strength to external load is also a random variable. The range of random safety factors is:

Among them, Î² is the reliability index, CR, CS represent the compressive strength of the carton and the coefficient of variation of the external load, respectively.

From the test data and the calculation results in Table 1, the coefficient of variation of the carton compressive strength and external load can be obtained. Assuming that the coefficient of variation remains unchanged, the range of random safety factor calculated from equation (8) in the case of a reliability pr = 0.99 is: 1 â‰¤ n â‰¤ 2.856. In the calculation and calculation of the current compressive strength of corrugated boxes, the safety factor is generally taken as 4 to 5. It can be seen that the current strength design method is somewhat safe.

Source: China Public Venture Network

Tipping machines,

Our Tipping machines is used to tip the Tipping Film on both end of shoelace, or bag handle rope lace. there is fully Automatic Tipping Machine. We have max 1.5meter, 2meter, 2.5meter according to customer demand. We also have semi auto Tipping Machine, which have no length limited, but need one operator to work.

The advantages of the tipping machines,
1, the processing temperature can be adjusted automatically, normally in 50Â°to 60Â°.When reaching the set temp, it will be fixed automatically.
2, the main motor has the overload protection function.
3, the machine is equipped with special safety device and the base of the mold is made of high quality casting, so, the mold can be used for a longer life.
4, strong structure and safe operation and good materials and good brand electrical parts, technically and mechanically, the whole machine can be used for at least 20 to 30 years without any problems.
5, the machine has the function of programming protection, under which function the machine parts will not be easily broken because of reverse or wrong power connection. When power cable is wrongly connected, the machine will not run.
6, the machine will stop working automatically when there is no tipping film feeding, under which function the machine idle running will be avoided.

Tipping Machine

Tipping Machine,Tipping Film,Automatic Tipping Machine,Transparent Tipping Film, semi auto tippin machine

DongGuan FeiYang Packaging Machinery Equipment Co., Ltd , http://www.feiyang-machinery.com